An-Najah Staff

A potentially-economic three-fold strategy, to use solid olive wastes in water purification, is presented. Firstly, oil remaining in solid waste (higher than 5% of waste) was recovered by the Soxhlet extraction technique, which can be useful for the soap industry. Secondly, the remaining solid was processed to yield relatively high-surface area active carbon (AC). Thirdly, the resulting carbon was employed to reversibly adsorb chromate ions from water, aiming to establish a water purification process with reusable AC. The technique used here enabled oil recovery together with the production of a clean solid, suitable for making AC. This process also has the advantage of low production cost.

A potentially-economic three-fold strategy, to use solid olive wastes in water purification, is presented. Firstly, oil remaining in solid waste (higher than 5% of waste) was recovered by the Soxhlet extraction technique, which can be useful for the soap industry. Secondly, the remaining solid was processed to yield relatively high-surface area active carbon (AC). Thirdly, the resulting carbon was employed to reversibly adsorb chromate ions from water, aiming to establish a water purification process with reusable AC. The technique used here enabled oil recovery together with the production of a clean solid, suitable for making AC. This process also has the advantage of low production cost.

Full Text

Recycling of plastic poses several concerns to manufacturers. The most important concern is the unpredictable of their mechanical properties (modulus of elasticity, tensile strength and ductility). Olive solid waste, an abundant material usually thrown into land causing harms to environment was mixed with HDPE plastic and used as a filling material. The mixture was fed to a house made extruder operating at different speed and temperature. Two carbon particle sizes range (less than 150 µm and 180–250 µm) were used. The effect of carbon contents from 0 to 10% wt/wt and operating conditions were tested on the mechanical properties of the recycled HDPE plastic. It was found that up to 5% wt/wt carbon of less than 150 µm resulted in a noticeable improvement of modulus of elasticity and tensile strength. The optimum value of modulus at carbon particle size 180–250 µm was found at 2.5 olive solid carbon content. Increasing screw speed was found to increase tensile modulus and strength of used plastic. This was related to melt viscosity and reduction in particle size. An increase in processing temperature was found to improve tensile properties up to certain point where degradation of polymeric matrix begins to occur and therefore tensile properties deteriorate.

A potentially-economic three-fold strategy, to use solid olive wastes in water purification, is presented. Firstly, oil remaining in solid waste (higher than 5% of waste) was recovered by the Soxhlet extraction technique, which can be useful for the soap industry. Secondly, the remaining solid was processed to yield relatively high-surface area active carbon (AC). Thirdly, the resulting carbon was employed to reversibly adsorb chromate ions from water, aiming to establish a water purification process with reusable AC. The technique used here enabled oil recovery together with the production of a clean solid, suitable for making AC. This process also has the advantage of low production cost.

Full Text

Recycling of plastic poses several concerns to manufacturers. The most important concern is the unpredictable of their mechanical properties (modulus of elasticity, tensile strength and ductility). Olive solid waste, an abundant material usually thrown into land causing harms to environment was mixed with HDPE plastic and used as a filling material. The mixture was fed to a house made extruder operating at different speed and temperature. Two carbon particle sizes range (less than 150 µm and 180-250 µm) were used. The effect of carbon contents from 0 to 10% wt/wt and operating conditions were tested on the mechanical properties of the recycled HDPE plastic. It was found that up to 5% wt/wt carbon of less than 150 µm resulted in a noticeable improvement of modulus of elasticity and tensile strength. The optimum value of modulus at carbon particle size 180-250 µm was found at 2.5 olive solid carbon content. Increasing screw speed was found to increase tensile modulus and strength of used plastic. This was related to melt viscosity and reduction in particle size. An increase in processing temperature was found to improve tensile properties up to certain point where degradation of polymeric matrix begins to occur and therefore tensile properties deteriorate.